Pathloss 5.1 - Revision history

Pathloss 5.1 - revision date September 19, 2017

• Fix to AntRad create_rxselectivity_calc

Pathloss 5.1 - revision date August 17, 2017

• Fix problem with Area and Local study throughput display criteria that could cause a crash.
• Path parameters for each leg of a passive link are now displayed correctly when clicking on the path profile in Transmission Analysis
• Small crash fix regarding long antenna codes.
• The Transmission Detail Report for adaptive modulation radios now displays the space, frequency, and quad diversity improvement factors that apply to the reference state.
• Print notes now works for Transmission Detail, Transmission Summary and Composite reports.
• Fixed Empirical Studies bug that could show polygon extending to the corner of the screen on some terrains.
• Removed (OFDM) Language

Pathloss 5.1 - revision date July 18, 2017

• Minor memory overrun fix.
• Diffraction loss with single obstruction near site 2 wasn't using the proper near field calculation.
• .pl5 files deleted from network display sent to recycle bin if possible.
• Fixed Interference case detail report crash.

Pathloss 5.1 - revision date June 12, 2017

• Opening a Pathloss 5.0 adaptive modulation file in Pathloss 5.1 could incorrectly set the reference state in some cases.

Pathloss 5.1 - revision date June 1, 2017

• Opening a Pathloss 5.0 adaptive modulation file in Pathloss 5.1 could incorrectly set the reference state in some cases.
• Fixed crash when creating 'receive at base station' local study using adaptive modulation.
• Fixed Typos.
• Pl40 Export - Use TX Channels is now set properly.

Pathloss 5.1 - revision date April 18, 2017

• Fixed LOS_status thematic worksheet display problem.
• Vertical antenna discrimination is now used in interference calculations if the antenna file has all 8 patterns defined.
• Base station antenna heights in interference calculation could have been incorrect if the system was set to metric.
• Small fix to rtf report generation.
• Equipment index now warn about duplicate imports and check filter settings
• Adaptive radios now correctly sets the effective rx threshold if modulation states are committed. Each modulation state should be represented only once in each radio file
• FCC channel tables added to the equipmnt\freqplan directory

Pathloss 5.1 - revision date February 15, 2017

• Fixed bug that was causing inconsistent results on interference calculations.

Pathloss 5.1 - revision date February 1, 2017

• Fixed problems access ACU data in radio files from the ACU worksheet in transmission analysis.
• Fixed interference problem where OHLOSS profile would not complete over certain elevation DEMs.
• Modulation states and now be toggled off and on in PTMP links by clicking the TR button. (Radio needs to be re-imported from index first.)

Pathloss 5.1 - revision date January 16, 2017

• Fixed issue where the "TR" Button would not work after loading some microwave radios.

Pathloss 5.1 - revision date January 13, 2017

• Rain Unavailability in Minutes was incorrectly displayed for this configuration: ACM radio - summary display for all modulation states - worst month SES
• Pathloss 5 Link Standalone toolbar button fixed.
• Some context help buttons were not linking to the topics automatically.
• Optimize interference worksheet fix (take two)

Pathloss 5.1 - revision date January 9, 2017

• Better handling when reading radio data files curve formats.
• Buttons were not functioning in the Optimize interference worksheet (Right click on a site and select Interference)
• Fixed potential crash in autolink csv reports if there are very large values for certain site properties such as tower height.

Pathloss 5.1 - revision date November 30, 2016

• 5.0 ACM user entered powers are now maintained when opened in Pathloss 5.1
• Field margin in land mobile application was incorrectly displaying the site 2 field margin.
• Fixed bug in summary and detail reports that was incorrectly had the heading EIRP (should be ERP) when frequency was below 890 Mhz.

Pathloss 5.1 - revision date November 9, 2016

• Modified behavior when adding radio from index to worksheet. Different adaptive modulation radios can now be assigned at each end of a PTMP link. (PTP adaptive modulation links require the same radios on each end.)

Pathloss 5.1 - revision date November 2, 2016

• In the transmission analysis module, a value of 0 could be entered for frequency that would cause an erroneous improvement.
• Fixed crash in CtoI Area study when site were removed from the study by using the site list check boxes or by deleting base station.
• View study details for CtoI area studies now shows all receive signals included in study for each cell.
• Main windows were not sizing correctly on start up.
• Minor fixes to language
• Adaptive modulation links will now calculate free space and atmospheric absorption loss without needing to enter a radio code
• Additional checks are performed when creating a passive to ensure all requirements are met.

Pathloss 5.1 - revision date October 4, 2016

• Option to convert from 5.1 to 5.0 file format. Click "Operations - Convert .pl5 files to .pl4" to see this option. Converted files will be placed in a subfolder called \50Format.
• Fixed bug with PostgreSQL ODBC connector

Pathloss 5.1 - revision date September 15, 2016

• Antrad was crashing when opening files with long, but valid filenames.
• Convert .pl5 to .pl4 files was crashing if certain fields were too long - these are now truncated.
• When clicking the (A) button in the channel table to add ATPC from the radio file: The max ATPC is read from the ATPC_OPTIONS_DB field - NOT the "ATPC Top" figure in the modulation table.
• Link text import was not loading antenna data when a code was supplied for antenna 2 (space diversity)

Pathloss 5.1 - revision date September 6, 2016

Fixed a bug that could cause a program crash when manually entering threshold degradation in transmission analysis worksheet.

Pathloss 5.1 - revision date August 25, 2016

• Create point to point links: The "To group" is now used when connecting to nearest number of sites.
• Certain combinations of TX emission and RX selectivity curves in radio data files could intermittently produce a floating point exception on some computers. This resulted in a large filter improvement and effectively removed the interference case

Pathloss 5.1 - revision date August 18, 2016

• ATPC power reduction assignment when using a required receive signal value was calculated using the lowest modulation state data when it should have used the highest.
• Changing the reference power when using ETSI operation could be applied incorrectly to the other modulation states.
• Fixed crash when clicking Files - New in Pathloss Link while in a module that requires a profile.
• Changing the power option in the radio configuration dialog now resets the user powers.
• Changing the antenna in the antenna worksheet and then canceling out, not all calculations were reset to the original antenna.
• CSV Link report 1 Column alignment problem when exporting adaptive modulation files with the show summary for all states option.

Pathloss 5.1 - revision date July 18, 2016

• Shared Operation update window waits until program idle to request network synchronization.

Pathloss 5.1 - revision date July 6, 2016

• Fixed problem in handling some radio files where radio_type field could cause a buffer overrun.

Pathloss 5.1 - revision date June 30, 2016

• Local study azimuth fix
• Fixed potential interference calculation problem when using a very specific frequency separation.
• GIS file is not removed when loading a new link file with matching datum parameters.
• AntRad version 4 radio curves edit window was not showing the dialog bar at the top.
• Add to group functionality returned to "Import Pathloss data file" dialog box.

Pathloss 5.1 - revision date June 15, 2016

• Change to over building diffraction loss calculation - revert to previous method.
• Local study was incorrectly determining azimuth for some antenna patterns.
• For ACM radios, a User Power can be set for all modulation states (ANSI and ETSI) during radio import or by clicking the TR button.
• Fixed crash when clicking ACU import index button in ACU worksheet.
• Fixed crash in CSV Link export 2 when exporting adaptive modulation columns on non-adaptive links.
• Fixed format problem for channel #12 export information.
• Improved handling of floating lock license release.

Pathloss 5.1 - revision date June 3, 2016

• Import Pathloss data file bug fix.

Pathloss 5.1 - revision date June 2, 2016

• Added the option to copy detailed, per radial, HAAT information. This is done in the HAAT calculation in the Pathloss 5 Link Site Data dialog box.

Pathloss 5.1 - revision date May 27, 2016

• Fixed problem when importing some radios that could set the power level to 0

Pathloss 5.1 - revision date May 26, 2016

• Fixed bug in interference calculation. When calculating interference between overlapping groups or selections, some space diversity or XPIC cases were not reported.
• Pathloss Link window now closes automatically when opening a new network for shared use.
• When setting groups visibility there is the option to use an exclusive mode. In this case links will not be shown if the site on either end is not shown.

Pathloss 5.1 - revision date May 18, 2016

• Pathloss now saves manual changes to the reference state power in adaptive modulation radio links.
• Fixed bug in AntRad that would cause a crash when saving conventional Microwave radio in ASCII format.

Pathloss 5.1 - revision date May 9, 2016

• Corrected bug that could cause a crash if Obstruction fading routine was run on an adaptive modulation path showing detailed reference state information.
• Corrected bug where CSV Link report II would output identical rows for every leg of a passive repeater link.
• Change to Antrad that can read 5.0 raf files with modulation states starting on rows other than one.

Pathloss 5.1 - revision date May 2, 2016

• Fixed problem with DEMS that use US State Plane Projections in feet or US survey feet.
• The Pathloss license server now resides on an amazon server. You may need to update your firewall settings after applying this update. Contact CTE for details.

Pathloss 5.1 - revision date April 25, 2016

• Removed small utility init_flo.exe which was generating false positives in some anti-virus software.
• Fixed bug that was preventing ETSI power levels from being limited to the reference modulation power.
• Transmission Analysis window drawing were not showing the correct figures for the reference state. (adaptive modulation)
• Fixed bug that prevented DTED data from being loaded.

Pathloss 5.1 - revision date April 19, 2016

Major bug fix that would cause a program crash during activation if a connection to the license server was not available.

This correction required a full uninstall and reinstall.

Pathloss 5.1 - revision date April 18, 2016

• Fixed transmission detail and summary report problem that would not correctly display the channels frequency and ID's
• Added descriptive fields to Google Earth export: Azimuth, TX Channel ID, TX Power, RX Threshold, Link Type, Link Status, LoS Status, Site Coordinates, Site Type, Site Status and Tower Type.
• Manually entered path lengths in PL50 link are preserved after saving and loading.
• Availability rejection criteria for auto link design now appears for adaptive modulation regardless of display setting.

Release of Pathloss 5.1

• New development platform.
• Dynamic number of modulation states for adaptive modulation radios (unlimited number)
• Dynamic number of radio configurations (unlimited number)
• Improved transmission display options for adaptive modulation radios.
• Whole program memory management and stability improvements.
• Option to delete .pl5 file when deleting links from network display restored.
• Fixed possibility of crash on very specific path geometries that could occur when generating large studies.
• Blank site list elevations are update automatically after generate profile operation. (No Data Discrepancy dialog.)